source:Industry News release time:2023-02-07 Hits: Popular:Brand bar audio wholesale
1. Power
There is no direct relationship between the sound quality and power of the speaker. The power determines the louder that the speaker can make, and it feels how shocking the sound of the speaker can be.
According to international standards, there are two ways to mark the power:
The rated power (RMS: sine waves) refers to driving a 8Ω speaker within the rated range to specify the continuous simulation signal of the waveform. After there is a certain interval and repeat a certain number of times, the speaker does not cause any damage to the maximum power;
Instant peak power (PMPO power) refers to the maximum power that the speaker can bear in a short time.
What are the indicators of the good or bad of the speaker?
The Federal Trade Commission stipulated the standard for power in 1974: driving a 8Ω speaker load with two channels, and the effective tile count measured when the harmonic distortion is really less than 1%in the range of 20-20000Hz, which is the amplifier of the amplifier. Output power, the label power is the rated output power. In order to cater to consumers' psychology, merchants are marked with instant (peak) power, which is generally about 8 times the rated power.
The power of the speaker is not as big as possible, the best applicable. For the 20 -square -meter room of ordinary family users, the real 60W power (referring to the effective output power of the speaker 30W × 2) is enough, but The larger the reserves of the amplifier, the better, it is best to be more than twice the actual output power. For example, if the speaker output is 30W, the power amplifier is best than 60W. For the HIFI system, the power amplifier power drives the speaker is very high.
2. Frequency range and frequency response
Frequency range: refers to the range between the minimum effective backing frequency and the highest effective return frequency that can be replaced by the audio system;
Frequency response: refers to the phenomenon of increasing or attenuation of the sound pressure generated by the speaker with the frequency of frequency, and the phase of the phase is performed when the audio signal that is connected to the system with a constant voltage output is The relationship between the associated between the phase and the frequency (variable) is called the frequency response, and the unit decibel (DB).
Popular recommendation
I3 Small bar sound Vendor
2021-07-26Dance Stack Overview Car stereo Factory
2021-07-16Resolution 4S Skeletal Bar use audio Vendor
2021-07-16D2 AMPS Bar speakers wholesaler
2021-07-26PSM18 POINT SOURCE MONITOR Speaker bar Factory
2021-07-16A3 Home ktv audio Merchant
2021-07-26F1201 School audio Vendor
2021-07-16EVO 7TL-215 Sound bar Factory
2021-07-17F1 Mini bar sound Factory
2021-07-26A28 CARDIOID SUBWOOFER Learning audio Merchant
2021-07-26XD18C Big sound bar Merchant
2021-07-26C12 Bar hall sound Merchant
2021-07-26Design concept of bar acoustics
2022-11-19How to make bar audio equipment show better sound quality?Domestic bar audio Vendor
2021-11-30What is a back-to-listening speaker
2022-01-12Shanghai high-end bar MASTER special audio---Mateng audio
2022-05-25KTV sound system debugging method.Bar audio service
2022-11-02Compressor--a common human operation failure in professional audio.Shaanxi Conference Room Audio
2022-06-09What is the status of entertainment audio in the market?
2022-03-07The cost of holding a concert in rainy days is high. How to choose the sound?Bar needs sound
2022-02-21The special audio for the Chengdu DNA Internet Red Bar is provided by Maarten Audio
2022-09-26Sound field design instructions for entertainment audio
2022-02-19Talk about the 4 elements of professional audio power amplifier and speaker matching
2021-09-11How to choose the right video conference system solution.Kunming Bar Audio Factory
2022-07-12