source:Industry News release time:2022-09-07 Hits: Popular:Brand bar audio wholesale
Professional audio systems are composed of many different functional devices. After designing the audio system according to the use requirements and selecting the equipment used, these discrete devices should be connected according to the design requirements to form a complete set of audio systems that can achieve the design requirements. For a fixed installation system, the equipment should be installed in a cabinet, and all system connections should be fixedly installed in accordance with certain standards and specifications. For mobile systems, such as temporary installations such as concerts and outdoor performances, effective temporary fixing measures should be taken for equipment and cables to ensure their safety.
The connection and installation of the audio system involves many engineering issues, including the design and construction of the audio control room, the pipeline engineering of the audio system cable, and the power supply of the system. Here are some issues that need to be paid attention to in the transmission of audio system signals.
1. Impedance matching
The signal input port is also the load of the signal output port, and the impedance matching between them needs to be within the range to meet its requirements, which generally depends on the design requirements of the signal output device. In order to achieve the best transmission state of the audio electrical signal, the impedance of the signal input interface must meet the impedance matching requirements of the signal source output interface to its load, otherwise, it will affect the working state of the audio equipment and cause distortion of its output signal. In severe cases, there is even a risk of damaging the audio source equipment.
Theoretically, when the output impedance is equal to its load impedance, the transmission efficiency of the signal is the highest. However, if the output impedance is greater than the load impedance, most of the signal power will be lost on the signal output circuit, which is obviously not conducive to signal transmission. Therefore, audio equipment is usually designed so that the input impedance is greater than the output impedance.
The connection of general audio equipment, as long as the load impedance is greater than the impedance of the signal output end, can make it work normally. However, the input impedance of the audio equipment cannot be designed to be too high or too low. If it is too high, it will reduce the anti-interference of its feeder. If it is too low, it will cause its frequency response index to decrease.
2. Signal transmission level
The purpose of the audio system connection is to transmit signals. The optimal state of audio signal transmission requires that the level value output by the signal source must be greater than or equal to the sensitivity of the input interface. Otherwise, the signal-to-noise ratio index of the signal will deteriorate. The gain of the line input and output circuits on professional audio equipment is generally set at 0dB, that is to say, the equipment neither amplifies nor attenuates the level of the input or output signal, so that it can be maintained during the transmission process. Its level value remains unchanged, which is mainly to ensure that the adjustment of the level control unit can be numerically guaranteed.
In the system connection, attention should be paid to the matching of output and input levels. Otherwise, clipping distortion may be caused, or the excitation signal may be insufficient, resulting in a decrease in the signal-to-noise ratio of the entire system. Usually the connections between audio equipment (mixers, peripherals, amplifiers) are at line level to transmit signals. There are generally two line standards, one is +4dB (1.228V), and the other is 0dB (0.775V). The line level of the equipment used in the system should be unified, so that it will be more convenient to adjust and use. In addition, some sound processing equipment, especially the effector, in order to take into account the needs of electro-acoustic musical instruments and professional sound systems, the interface level conversion function is set. -10dB, -20dB several gears, when using the sound reinforcement system, you should pay attention to adjust it to +4dB gear.
Popular recommendation
Resolution 4E Bar speakers Factory
2021-07-16Resolution 5E Big sound bar Vendor
2021-07-16Minibass 212 Bar bar sound Merchant
2021-06-09D80DSP Large bar sound Vendor
2021-07-26EVO 6E KTV audio Merchant
2021-07-16DS 210Sound bar Vendor
2021-07-17EVO 7TL-215 Sound bar Factory
2021-07-17Resolution 1.5TT Marten Audio company
2021-07-16Dance Stack Overview Car stereo Factory
2021-07-16PSM18 POINT SOURCE MONITOR Speaker bar Factory
2021-07-16AX 8 KTV audio price
2021-07-17MST 10Sound bar sales
2021-07-17Conference room audio and video system solutions.Bar use sound price
2022-04-27These are just the basics! Explanation of common terms used by sound engineers
2022-04-21Lanzhou T61 CLUB special audio equipment is provided by Ma Teng Audio
2022-04-12How to adjust the stage sound in the performance?
2021-09-09The deadly factor of the speaker in summer
2022-09-15Troubleshooting common problems during recording.Audio for bars Manufacturing
2022-04-18Combination rules and requirements for professional audio equipment.Gymnasium audio Vendor
2021-11-10Shanghai MASTER popular bar special audio ---- Ma Teng Audio
2022-04-24Shanghai popular Internet celebrity MASTER bar special audio--Mateng Audio
2022-10-11How to do it to truly ensure the effect of home theater.Professional bar sound company
2023-03-25Home theater audio purchase six points.Conference room amplifier audio
2022-06-21How to configure conference room audio.Xi'an Bar Audio price
2022-05-19