Bar audio brand|Bar audio sales|Bar audio service|Bar sound company|Bar audio solution-Shenzhen Ma Teng Audio Technology Co., Ltd.

News

The perfect sound system with supreme attentive service has been recognized by a wide range of users

Home  -  News  -  Industry News

How to prevent sound system whistling.Home ktv audio Factory

source:Industry News release time:2022-07-05 Hits:     Popular:Brand bar audio wholesale

  XD12 Brand bar audio Vendor

  Howling of the audio system refers to the positive feedback of sound between the pickup and the speaker. This positive feedback goes through an infinite loop, thus forming the phenomenon of self-excitation and feedback. The pickup distance of the microphone is inseparably related to the on-site acoustic environment and the isolation between the microphone and the speaker. Together, we call the "sound transmission gain" of the system. Under reasonable system configuration, equipment placement and acoustic environment conditions, the sound transmission gain will be improved.

  Reasons for audio whistling: overloaded level output, more environmental reflections, too close the distance between the microphone and the speaker, relative pointing angles, uneven frequency response curve of the device, etc.

  Hazards from whistling:

  1. Damage the power amplifier and other electro-acoustic equipment.

  2. Affect the sound reinforcement quality.

  3. Destroy the atmosphere of the event site.

  To put it simply, the conditions for howling to occur must meet the following three points:

  1. Use both the microphone and the speaker at the same time.

  2. The sound reproduced by the audio system can be transmitted to the microphone through the space.

  3. The sound energy emitted by the speaker is large enough, and the pickup sensitivity of the microphone is high enough.

  Solution:

  Eliminating feedback whistling starts with the necessary conditions for generating feedback whistling. As long as one of the conditions can be destroyed, the goal can be achieved.

  1. Adjust the distance method

  One of the most effective ways to avoid howling and increase the volume of the amplification is to place the microphone as close to the sound source as possible.

  2. Shortening the distance between the sounding equipment and the audience can actually increase the loudness of the sound reinforcement.

  3. The farther the microphone is from the speaker, the better. The microphone should be placed on the back of the speaker's radiation direction, or not in the front of the speaker.

  4. Broadband notch method, since the frequency curve of the microphone pickup and sound-generating equipment is not an ideal flat straight line, the frequency response of the system can be adjusted to an approximate straight line through the EQ of the audio processor, so that the gain of each frequency band is basically the same, which can be Relatively improve the sound transmission gain of the system.

  5. The feedback suppressor method, also known as the narrow-band notch method, uses an automatic audio feedback suppression device, which can automatically track the frequency of the feedback point, automatically adjust the Q value bandwidth, and automatically eliminate the acoustic feedback while maximizing the protection of the sound quality. . The principle is to suppress howling through a narrow notch, while maximizing the protection of the sound from being affected.

  6. Inverse cancellation method to prevent self-excitation is common in high-frequency amplifier circuits.

  In the audio amplifier circuit, two microphones of the same specification can be used to pick up the direct sound and the reflected sound respectively, and the reflected sound signal can be canceled out of phase before entering the power amplifier through the inverting circuit, which can effectively prevent the self-excitation of howling.


Read recommendations:

DS15 Bar speakers Merchant

F101 Marten Audio Vendor

Resolution 5S skeletal Concert sound Vendor

Equalizer debugging.Conference room audio quotation

What should I pay attention to when installation of professional KTV audio?Professional performance

Previous:Some common faults about audio equipment.Guiyang Bar Audio wholesaler Back to list Next:Hohhot ID-X Special Audio for Party Bar---Mateng Audio.Home ktv audio Processor

Popular recommendation

I3 Small bar sound Vendor

2021-07-26

I8SUB Gymnasium audio Vendor

2021-07-26

Resolution 1.5 ktv bar sound Vendor

2021-07-16

Resolution 2 SHCar stereo Vendor

2021-07-17

XQ42 Bar speaker wholesaler

2021-07-26

F55 Bar speaker company

2021-07-16

Resolution 4T Touring Bar use sound Vendor

2021-07-16

A2 Dalian Bar Audio Vendor

2021-07-26

Infrabass 218Sound for bars Vendor

2021-07-14

Resolution 5E Big sound bar Vendor

2021-07-16

RM15 Audio for bars Vendor

2021-07-15

XQ48 Bar sound bar Merchant

2021-07-26

Is the audio debugging in the conference room noisy? These three methods can be solved quickly!

2022-11-12

Attention audio and lighting industry! 5 solutions to teach you to build the stage of the annual mee

2022-04-23

The role of the audio

2023-04-14

The difference between full-range speakers and crossover speakers

2021-09-11

Preparation before commissioning.High-end bar audio Vendor

2021-11-23

Chengdu DNA bar sound engineering is provided by Maarten Sound

2022-11-02

Detailed explanation of commonly used cables for audio equipment There is a mystery in connecting pl

2022-04-19

How to improve the sound effect of multimedia conference system.Bar speakers Vendor

2021-12-07

How to improve the sound quality of the already formed speakers?

2022-04-02

Detailed explanation of commonly used cables for audio equipment There is a mystery in connecting pl

2022-04-20

Dingyuan TAICHIPARTY bar audio project is provided by Mateng Audio

2022-10-24

How to choose the five differences between the digital amplifier and the simulation amplifier of the

2023-02-17