source:Industry News release time:2021-10-21 Hits: Popular:Brand bar audio wholesale
What causes noise in professional entertainment audio
In the sound system of performance stage such as recording and live sound reinforcement, the noise problem is a common and very headache problem. Generally, the more devices that make up the audio system, or the longer the transmission distance, the greater the background noise of the system, and even the professional audio system cannot perform normal recording or amplification work. The mechanism of sound system noise formation is relatively complicated. Ding Taifeng Audio Company will now analyze and discuss the main causes and solutions of these sound system noises.
Causes of noise
1. Circuit noise inside the device
Professional entertainment audio equipment has an indicator-signal-to-noise ratio. Due to the electrical noise generated by the internal electronic components, when one device works alone, the required index can be achieved, but when multiple devices are cascaded, the noise will accumulate and increase. In practical applications, some low-grade civilian audio equipment will have a lot of AC noise due to poor internal power supply filtering, which will sometimes cause serious noise in professional audio systems.
2. Power interference noise
The external interference of professional audio equipment, in addition to electromagnetic car radiation, the introduction of interference noise in the power supply part will be another main cause of noise. The urban power grid has formed a very serious source of interference due to the joint access of various lighting equipment, power equipment, and control equipment.
For example, lighting control equipment, air conditioners, motors and other equipment connected to the same power grid will generate spikes, surge currents, and ripple voltages of different frequencies on the power line, which will enter the power supply of professional audio equipment through the power line. There will be some interference noise that cannot be effectively filtered by the power circuit of the audio equipment, and noise will inevitably form inside the equipment. Especially high-power equipment with electromagnetic compatibility in the same power grid that does not meet the requirements is the main reason for interference with audio equipment.
3. Electromagnetic radiation interference noise
Environmental stray electromagnetic radiation interference, such as high-frequency electromagnetic radiation interference of communication equipment such as mobile phones and walkie-talkies, electrical pulse radiation such as elevators, air conditioners, car ignitions, and electric welding in the surrounding environment. The generated radiation will be directly mixed into the transmission signal through the audio transmission line to form noise, or pass through the casing of poorly shielded equipment and interfere with the internal circuit of the machine to generate interference noise. Practice has shown that in some special occasions, such as studios where a large number of thyristor dimming equipment is used, if reliable shielding and grounding measures are not taken, the noise will be very serious.
4. Ground loop noise
In a professional entertainment audio system, the entire system must be well grounded, and the grounding resistance must be less than 4 ohms. Otherwise, the induced charges generated by the equipment in the professional audio system due to various radiation and electromagnetic induction will not be able to flow into the ground, resulting in a noise voltage superimposed on the audio signal.
If there is a ground potential difference between the ground wires of different devices due to the difference in ground resistance, or there is a loop in the internal ground of the system, ground noise will be caused. When two different professional audio systems are interconnected, noise may also be generated. The noise is caused by the direct connection of the ground wires of the two systems.
5. Circuit noise inside the device
Professional entertainment audio equipment has an indicator-signal-to-noise ratio. Due to the electrical noise generated by the internal electronic components, when one device works alone, the required index can be achieved, but when multiple devices are cascaded, the noise will accumulate and increase. In practical applications, some low-grade civilian audio equipment will have a lot of AC noise due to poor internal power supply filtering, which will sometimes cause serious noise in professional audio systems.
Popular recommendation
I5 Concert sound Merchant
2021-07-26AX 8 KTV audio price
2021-07-17I8SUB Gymnasium audio Vendor
2021-07-26D2 AMPS Bar speakers wholesaler
2021-07-26A3 Home ktv audio Merchant
2021-07-26XD10 KTV audio manufacturer
2021-07-26Minibass 212 Bar bar sound Merchant
2021-06-09XD18C Big sound bar Merchant
2021-07-26Bass Reflex Range Bar hall sound Vendor
2021-07-14Infrahorn Speaker bar wholesale
2021-07-14F121Car stereo wholesaler
2021-07-14AX 88KTV audio sales
2021-07-17Some common faults about audio equipment
2022-07-04Dongguan PARTY MASTER (original century) special audio for popular bars---Mateng Audio
2022-08-03What are the parts of the sound
2022-08-19What are the precautions for using professional audio equipment?
2022-07-18What are the details of professional audio equipment.Bar music sound
2022-04-09Professional conference audio-how important is the debugging method.Campus outdoor audio Vendor
2021-11-11Wireless Microphone Signal Quality and Distance.Conference room audio speakers
2022-06-10How to adjust the stage sound in the performance?
2021-09-09Several Factors Affecting the Use Quality of Conference Audio Equipment.Qingdao Conference Room Audi
2022-06-14Steps to debug professional audio engineering equipment
2021-09-23Zunyi FIRST ROOM bar audio system Ma Teng audio
2022-10-31Chongqing WUDU Unbounded Space Audio recommends MaTeng Audio.Bar sound design
2022-03-01