source:Industry News release time:2022-04-07 Hits: Popular:Brand bar audio wholesale

There are many kinds of audio equipment, and our audio engineer needs to adjust each audio equipment. The human operation faults we are talking about mainly occur during the performance, such as silence, staccato, feedback, noise and so on.
1. The channel level attenuation switch of the mixer: Some mixers add a level attenuation switch of about 20dB before the gain knob. When the CD and other audio sources are input from the high-impedance port, due to the high level, it may be It is appropriate to press this switch to attenuate the audio signal by 20dB.
2. Mixer gain adjustment: Some sound engineers don't know the importance of channel gain, so they adjust the knob randomly, sometimes turn off the gain knob, and even press the 20dB level attenuation switch at the same time, thinking about this time How small will the sound be?
3. Adjustment of mixer equalization group: As the name suggests, the mixer is mainly used to adjust the tone, and the adjustment of the tone mainly depends on the equalization group. It is very simple to say, it is nothing more than high school bass plus a few corresponding frequency selection knobs. Although the sound may not be very good under normal operation, there will be no performance accidents. However, some sound engineers sometimes turn the balance knob boldly. If the bass is increased too much, the burden on the entire power amplifier and speakers will be greatly increased, which may damage the equipment, and the sound will be easily distorted.
4. AUX adjustment of the mixer: Everyone AUX is mainly used to send signals to the effector. In a mixer, if we send the signal effector from AUX6, after the effector processing, if we output 2 signals to the mixer Channels 23-24 of the audio console, then do not turn on the AUX6 knob in the two channels 23-24 at this time, otherwise the signal will flow back to the effector after being processed by the effector just now.
5. Mixer pan: The pan knob is often regarded as an optional thing, but when we use the left or right output volume of the total output, we must pay attention to the pan. If you use the total output right output signal but the audio and image of the mixer channel are all hit to the left, it will cause a silent failure, which needs attention.
6. Mixer monitor and mute switch: Generally, the mixer monitor and mute switch are close together. Be sure to see clearly when operating. If you press the mute switch by mistake when pressing the monitor switch, it will also cause a silent failure.
Popular recommendation
F118 MK2 Brand bar audio sales
2021-07-14AX 88KTV audio sales
2021-07-17A1 Car stereo manufacturer
2021-07-26EV O7T Speaker bar Vendor
2021-07-16XQ42 Bar speaker wholesaler
2021-07-26Minibass 212 Bar bar sound Merchant
2021-06-09SB 210A Bar brand audio Vendor
2021-06-08BR132A Bar speaker wholesale
2021-07-14F315 Mini bar sound Vendor
2021-07-14DS 210Sound bar Vendor
2021-07-17Evolution 7E Sound bar Merchant
2021-07-16A3 Home ktv audio Merchant
2021-07-26What is the status of entertainment audio in the market?
2022-03-07Professional audio system installation.Conference room special audio
2022-06-02The difference between full-range speakers and crossover speakers
2021-09-11Six aspects to pay attention to when buying KTV speakers
2022-03-14How do traditional speaker manufacturers transform?Audio equipment bar company
2022-10-12How to plug in the host computer audio How to connect the audio cable to the host computer.Bar use a
2021-12-16What are the special requirements of the KTV audio device for speakers?Bar use audio direct sales
2023-03-28Key Points of On-site Control of Feedback Suppressor in Stage Sound System
2022-05-09The special audio for the Chengdu DNA Internet Red Bar is provided by Maarten Audio
2022-09-26Teach you to solve the "boss difficult" failure in the KTV system
2022-10-10What kind of sound is popular now?
2022-03-25How to design and choose conference room sound reinforcement system
2022-05-21