source:Industry News release time:2022-05-06 Hits: Popular:Brand bar audio wholesale
1. Connect the negative end of the 9V battery holder of the wireless microphone to a dense spiral with enameled wire, and fix it on the back of the tongue plate at the tail of the wireless microphone. The V segment is longer (winding to the end at a diameter of 2.5MM and then back to the starting point), and the U segment is shorter. (In the diameter of 4MM around to the head squashed).
2. Just connect the negative pole of the 9V battery to the battery shell, so that the transmitting antenna of the wireless microphone can be extended through the battery shell, which can increase the transmission distance and prevent the frequency band and frequency running.
3. Those who have the ability to disassemble the wireless microphone. . Pull out the tail more than two inches, revealing more than half an inch of circuit boards, find the position of the launch tube, solder it at the 1P capacitor (or a few P capacitors and the smallest capacitor), and wind it into a dense spiral with enameled wire, and fix it in the groove of the wireless microphone tail. , the outer diameter of the spiral is about less than the width of the slot, and it is flattened and fixed in the slot. Note: The wireless microphone with the 5th battery is not suitable for this side, because the wireless microphone with the 5th battery has used the battery shell.
4. If the frequency band is staggered. Please open the cover of the serial frequency receiver, keep the antenna lead-in away from the inductor and the mid-cycle, etc., and walk on the top or side to prevent the antenna signal from being directly serialized into the inductor and the mid-cycle (resulting in secondary tuning). There may be some effects, you can try it.
5. Sometimes it is useless to stagger the frequency points. Use multiple wireless frequency points in the same place. Two of the frequency points will produce the third frequency point, just like throwing two stones in the river, the third wave will be generated after the two waves interfere. Since the 2 waves are similar in frequency, the 3rd wave is also similar to him, and the 3rd wave will interfere with their "aunts and uncles". In general, the manufacturer will avoid this situation in advance, but there are also unavoidable ones. Therefore, through practice, we must understand which frequency points are the frequency points that can live in harmony.
6. When purchasing a VHF or UHF microphone, generally stagger the frequency by at least 25KHz.
7. The length of the antenna is inversely proportional to the frequency. The higher the frequency, the shorter the wavelength and the shorter the antenna.
8. The antenna lead point can be selected: 1. The negative terminal of the battery clip, 2. Or the emitter of the transmitting tube. The emitters of all transmitting circuits are connected with a minimum capacitance (1P or several P), which can be used to find the capacitance at the same time. To determine the lead point and the emitter of the wireless microphone with two No. 5 batteries, it is invalid to use this method, because it has used the battery shell to transmit the signal, so its effective distance can reach 150 meters.
Popular recommendation
F215 MK2 ktv bar sound Factory
2021-07-14F88 Car stereo Merchant
2021-07-16Resolution 2 S8KTV audio Vendor
2021-07-17F121Car stereo wholesaler
2021-07-14Resolution 4E Bar speakers Factory
2021-07-16A1 Car stereo manufacturer
2021-07-26XQ42 Bar speaker wholesaler
2021-07-26D2 AMPS Bar speakers wholesaler
2021-07-26Resolution 5S skeletal Concert sound Vendor
2021-07-16EV O7T Speaker bar Vendor
2021-07-16Resolution 4S Skeletal Bar use audio Vendor
2021-07-16F1 Mini bar sound Factory
2021-07-26Shanghai MASTER CLUB special audio equipment is provided by MASTER Audio
2022-07-22How to adjust the sound? Basic method of debugging audio.Bar audio price
2022-02-21Chongqing DNA CLUB professional audio is provided by Mateng Audio
2022-01-24Hohhot ID-X special audio equipment for popular bars---Mateng Audio
2022-04-02How to arrange the conference room with video conference system.Car stereo Factory
2022-04-22The difference between professional audio and civil audio technology.High-end bar audio Vendor
2021-12-08How to set the feedback suppressor in professional audio system?
2022-05-10KTV audio system power test method!Bar special audio direct sales
2023-02-18How to improve the sound quality of the already formed speakers?
2022-04-02Skills for debugging professional audio system steps.ktv bar sound
2022-04-06Pressure Limit Control in Professional Audio System
2022-02-26Domestic professional audio ranking
2022-03-26